|
|
Manufacture of AC / DC adapter housing
Vašíček, Lukáš ; Ohnišťová, Petra (referee) ; Žák, Ladislav (advisor)
The bachelor's thesis proposes an injection mold for the production of a plastic adapter. Based on the evaluation of the technological possibilities of the production of a plastic product, the technology of plastic injection was chosen. The first part of the work is devoted to a theoretical explanation of plastic materials, injection molds and machines. The practical part presents and develops a complete design of the injection mold, including the selection of a suitable material. The mold is designed four times with a cold inlet insert. At the end of the work is a technical - economic evaluation of production.
|
|
|
Metallization of technical plastics for lightweight traffic components with reduced fuel consumption
Sanetrníková, Dominika ; Boušek, Jaroslav (referee) ; Šimůnková, Helena (advisor)
The beginning of this thesis is dedicated to polymeric materials, which include plastics an composites. Plastics are shortly divided into two groups, thermoplastics and thermosets. The following part is the use of plastics and composites in traffic industry and briefly this work focuses on techniques of recycling of this materials. This work also focuses on the techniques of thin film deposition, electroless plating, electrodeposition as well and plating in the vacuum environment. special techniques of thin film deposition are also mentioned shortly. The coatings of polymer including cleaning and surface activation is introduced using various techniques including plasma treatment. The surface treatment of polyetheretherketone (PEEK) is included too. The final part describes performed experiments and discussion of results.
|
|
|
Recoverability of municipal waste plastics
Jedličková, Kateřina ; Gregor, Jiří (referee) ; Kropáč, Jiří (advisor)
The main aim of this bachelor thesis is identification of running costs and economical claims connected with production of secondary raw materials from separated plastic waste. It also includes a comparison between treatment of separated plastic waste and treatment of plastics that occur together with residual mixed municipal solid waste.
|
|
| |
|
|
Production single parts "Case of coil winding"
Rudolf, Bronislav ; Kandus, Bohumil (referee) ; Žák, Ladislav (advisor)
Bachelor´s thesis is elaborated in terms of branch B-STG engineering technology. Smoothing - out suggestion manufacturing engaged plastic parts from material PA66- GF25 FR by the help of injection technology. Firstly, the basic materials for injection are described, then is described injection principle, injection mold and injection machine. The practical part deals with their own forms of construction. In the inclusion is simple economics upward revaluation expense and surplus.
|
|
|
Production technology of plastic body aperture
Dluhoš, Jan ; Kebrle, Ondřej (referee) ; Kandus, Bohumil (advisor)
This thesis deals with the production of a plastic body of the aperture by the method of injection moulding. The work includes a design of the injection mould for the given component. First, an appropriate material for the moulded piece was chosen and then the necessary calculations for the injection mould were made. A quadruplex injection mould with a heated inlet nozzle and pullout cores was designed based on these calculations. Modular components were chosen when designing the injection mould. The next part of the thesis contains the selection of the injection moulding machine for the given mould. The conclusion contains a technical-economical evaluation including the cost estimating for the injection mould and cost estimating for one moulded piece.
|
|
|
Optimization of technological parameters of injection plastic parts
Ulrich, Josef ; Kebrle, Ondřej (referee) ; Kandus, Bohumil (advisor)
This thesis describes the optimalization of technological parameters during commissioning of injection mold manufacturing. In the introduction, there is general literary studies of plastics, injection molds, injection holding machine, injection holding technology and their effect on quality. The practical part includes an analysis of current state, calculation of injection parameters, moldflow analysis and sampling on the machine. Finally, there is choice of optimal injection holding parameters, design of workplace and technical-economic evaluation.
|
|
|
Production technology of the connector body from recykled material
Brhel, Michal ; Sedlařík, Vladimír (referee) ; Kandus, Bohumil (advisor)
Study developed during the Master's degree studies of Mechanical Engineering deals with the use of recycled plastic in the injection molding and its influence on the mechanical properties of the mold. Examined product is used in the automotive industry as a connector body. The housing is manufactured from a plastic material, polyamide. The annual production volume of 3 000 000 pieces. According to tests specified in standard USCAR2 regrind influence on mechanical properties and dimensions was evaluated. After the technical evaluation of the project, research was also judged from economic point of view. In this task, savings with the different content of the recycled material during production was calculated. The final chapters justify change of properties and they are proposing the use of recycled materials in practice.
|
|
|
Engineering plastics for specific applications
Vrátný, Martin ; Kebrle, Ondřej (referee) ; Kandus, Bohumil (advisor)
This bachelor’s thesis is focused on heat resistance and chemical resistance of plastics. The first part deals with properties and usage of selected plastics. The second part includes description of heat resistance and chemical resistance. Selected plastics are compared in table by their resistance. In conclusion the plastics are compared by detected data and suitability of plastics in environment with higher temperatures and aggresive chemical impacts.
|
|
|
Design and realization of extrusion head and connecting members for extrusion of circular plastic profiles
Novák, Jakub ; Veselý, Oldřich (referee) ; Koutný, Daniel (advisor)
In this work is developed a proposal for extrusion head for extruding plastic wires of small diameter. There is a new conceptual design of cooling, which allows shape extruded products already in the extrusion head and thereby eliminates the need for large cooling tanks. To determine the optimal design is used software named Virtual Extrusion Laboratory, which is used in practice for the simulation of the extrusion process. Then it is experimentally determined behavior of plastic material, when the temperature of the melt in the extrusion head is reduced.
|
guest ::
